Transactions Papers
AIST # | Title |
Charcoal Fines: Strategic Raw Material for Brazilian Steelmaking | |
Effects of Recycling Sinter Dust as Calcium Ferrite in the Sintering Process on Sinter Quality and Emission of CO2, NO and SO2 | |
Investigating the Use of Shaft-Level Tuyere Injection With Computational Fluid Dynamics | |
Investigation of the Thermally Thick Alternative Reducing Agent Behavior in the Raceway Zone | |
Heat Transfer in a BOF Converter | |
Theoretical Calculation Associated With Raising Scrap Ratio in BOF | |
Modeling EAF Carryover Slag Volume and LMF Lime and Ca-Aluminate Addition | |
A CFD Study of Alloy Dissolution and Homogenization in the Ladle Metallurgy Furnace | |
Sensor Instrumentation and Advanced Imaging of the Full-Scale Physical Twin Mold for Digital Data Generation During Continuous Casting | |
Methods for Model-Aided In-Line Measurement and Control of Cross-Sections in Wire Rod and Bar Mills | |
Nitrogen Composition and Its Effect on Magnetic Properties of Simulated Twin-Roll Cast Non-Grain Oriented Si Steel | |
Dynamic Recrystallization Behavior of a Ni-Containing Austenite-Based Fe-Mn-Al Steel | |
Implementing Dimensionality Reduction for Fundamental Assisted Analytics for End of Blow Chemistry Prediction in an LD Converter (FAA4LD) | |
Slag Splashing — Cold Model Comparisons and Equations for Industry Setup | |
Predicting the Dissolved Oxygen in Steel by Using Quick Carbon Analyzer at Energy Optimizing Furnace | |
Physical Modeling of Hot Metal Desulfurization Through Submerged Rotative Lance | |
Usage of CaO-Al2O3 Synthetic Slag on EAF Tapping for Steel Desulfurization | |
Transverse Slab Crack Reduction in Low-Carbon, Low-Alloy Steels | |
Slab Surface Cracking Characterization of Hyperperitectic Steels | |
Investigation of Argon Bubble Injection in Continuous Casting | |
Inclusion Density in Tundish Zones Using Fluid Flow Simulations | |
Avoiding Asymmetric Flows Caused by Off-Center Pouring Into the Tundish: A Novel Impact Pot Design | |
Effect of Dewpoint on the Evolving Spectral Emissivity of Advanced High-Strength Steel During Intercritical Annealing | |
Hot Rolling Roughing and Finishing Reduction Balance for Heavy-Gauge X80 | |
Low-Carbon High-Toughness Steel for Tank Car Applications | |
Effects of Atmosphere on Bright Annealed Stainless Steel | |
Decarbonization and Increased Productivity in the Reheating Furnace Using Hydrogen Fuel | |
Synthesis of Fe-Al-C Intermetallic Alloy via Fe2O3-Al-C Interaction at 1,550°C: Implication for Mill Scale Upcycling | |
Fiber Optic Raman Probe for On-Line EAF Slag Analysis | |
Effects of Slag Removal Method on the Process Parameters of Energy Optimizing Furnace | |
Investigation of Non-Metallic Inclusions During Primary Melting of Specialty Steels | |
New AOD Automation System at Cleveland-Cliffs Butler Works | |
Prediction of Austenite Grain Size Evolution in Wire Rod Rolling | |
In-Situ Observation of the Solidification of X70 Steel Using High-Temperature Confocal Scanning Laser Microscope | |
Nitrogen Control in the Basic Oxygen Steelmaking Process | |
Modeling of the “K” Compensation Factor of the Momentum Balance Equation in a Metallic Bath in the LD | |
Bubble Size Determination in a Half-Scale Curved Water Model Mold for Various Casting Conditions Using Imaging and Machine Learning | |
Bubble-Inclusion Interaction During Argon Bubbling in a Tundish: Assessment With Automated Inclusion Microanalysis and Data Analytics | |
Physical and Mathematical Modeling of Residence Time Distribution and Grade Transition in a Twin-Strand Slab Caster Tundish | |
Modeling of the Mixing Phenomena in the RH Vacuum Refining Process | |
A Possible Reason Why Ti-SULC Grades Are More Prone to CC Clogging Issues Than Other Al-Killed Grades | |
The Study of the Behavior of CaO-SiO2-Al2O3-Na2O-Based Mold Flux in 1,400°C by a Fiber-Optic Raman Sensor | |
Approach to Successful Development of Low-Carbon, Lean-Alloyed Cold-Rolled Galvanized HSLA 550 Sheet Steels | |
CO2 Reduction by Combining Methanation With the Blast Furnace | |
Instrumented Trial-Based Models for Efficient Electric Arc Furnace Operation | |
Is It Possible to Cast Bloom and Beam Blanks With the Same Secondary Cooling Setup? | |
Effect of Water Jet Nozzle Lead Angle on Descaling Efficiency | |
Laser Ultrasonic Inspection of Mash Seam Welds in a Steel Mill | |
Application of API 5L X65M Skelp With Accelerated Cooling to Small-Diameter Spiral Pipes | |
Optimum Metallurgical Processing of Cost-Effective API Grade Structural Steel for Standard, Sour and Gaseous Hydrogen Service Transmission Line Pipe Applications |